1. F00VC30057 Injector Solenoid Valve Spare Parts & Packaging List
| NO. | 1 | 2 | 3 |
| Picture |  |
 |
 |
| Name | Injector Solenoid Valve Assembly |
Clapboard |
Solenoid Valve O-Ring |
| Description | Injector solenoid valve part number: F00VC30057 | Prevent contact between the positive and negative poles of the solenoid valve | Ensure that the sealing performance between the solenoid valve and the injector reaches the standard |
| NO. | 4 | 5 | 6 |
| Picture |  |
 |
 |
| Name | Green Anti-Rust Bag |
Lining |
Injector Solenoid Valve Packaging Box |
| Description | Prevent injector solenoid valve from rusting | Prevent the injector solenoid valve from being damaged by external forces | Place the injector solenoid valve and accessories |
2. F00VC30057 Injector Solenoid Valve Technical Support
2.1. F00VC30057 Injector Solenoid Valve Utilized Location
| NO. | Name |
| A | RQ code, quantity correction code |
Pic No.3
2.2. Reasons for F00VC30057 Injector Solenoid Valve Not Working Normally
(1) There is air in the oil circuit of the engine fuel system.
(2) Vehicle injector solenoid valve oil supply system is not normal.
(3) Engine common rail system oil leakage or pressure limiting valve damage.
(4) There is a short circuit, cutting out and poor contact in the wiring harness connected to the injector solenoid valve of the vehicle.
(5) The long-term placement of the injector solenoid valve causes the anti-rust oil to solidify, and the internal components are stuck or the oil holes are blocked.
(6) Before installing, carefully check whether other components in the common rail system are damaged so as to prevent the injector solenoid valve from not working properly after being replaced.
2.3. F00VC30057 Injector Solenoid Valve Storage Standards
(1) Choose a Suitable Storage Place
The warehouse and cargo yard where the injector solenoid valves are stored should be kept clean and dry, and away from the factory buildings that generate harmful gases and dust; do not mix with acid, alkali, salt and other substances; the storage place should have a good drainage system; the cargo yard should be flattened with gravel or furnace ash etc. to enhance the water permeability of the surface layer to keep the reservoir area dry.
(2) Strict Storage Requirements
Strict inspections should be carried out when the injector solenoid valves are put into storage, the surface cleaning work should be done well to remove water traces, oil stains, ash and other dirt, remove the rust and do anti-rust treatment in time. Packaged injector solenoid valves must be protected from damage.
(3) Keep The Warehouse Dry And Do Moisture-proof Work
The relative humidity is usually below 70% for the injector solenoid valves placed in the room, and the corrosion of the injector solenoid valves is significantly reduced.
Injector solenoid valves must be stored in the warehouse, and they are forbidden to store in the same warehouse with commodities with high water content.
(4) StackProperly
After the injector solenoid valve is exposed to rain, the corrosion rate will increase significantly. The purpose of sealing is to isolate the injector solenoid valve from rainwater and humid air, so the warehouse window should be checked in time to avoid rainwater entering the warehouse.
If the injector solenoid valve package is damaged, it should be repaired or replaced; when the package is damp, the packaging material should be dried; if the original anti-corrosion and oil applied at the factory is found to be damaged or dried up, it should be cleaned and re-applied oil in time.
- It is forbidden to leave the injector solenoid valve exposed in the air for a long time.
- It is forbidden to store acid, alkali, salt and other substances together with the injector solenoid valve.
- The unpacked injector solenoid valve must be rust-proof during secondary storage.
